scrappystickyinkymess

Turtle Wrap book cover instructions

7 Comments

Finally, DS is on the train back to Uni.  So, FINALLY, here are the instructions for the Turtle Wrap book cover.

Although it is designed to be completely without adhesive, I think a line to hold the cover inside the wrap is maybe needed.  It stays in place set on a shelf, but handling the book, it’s perhaps not as secure as it could be. You don’t want someone flipping thru it and being mortified if the cover slips off. On the flip side, without the adhesive you can pull out the centre bit and replace it with a blank one – if you used it a bit like a Smash book, sticking in collected ephemera or jotting down daily thoughts, you may want to be able to do that.  Mine is meant to stay intact, so I think the line of adhesive is needed.

What you need: 

  • accordion folded inner pages – it is essential the FIRST and LAST page point in the same direction.  Doesn’t matter so much if that is forward or backward, as long as they match!

turtlewrap

  • two boards – cut about 1/2 inch bigger than the accordion, so 1/4 inch bigger on each side (mine is 5 x 5 so the covers are 5 1/2 x 5 1/2)

2turtlewrap

  • 2 Gelli prints at least 2 inches bigger in one direction than the cover.  Nothing too heavy, 90-120 gsm, so heavier weight printer paper to lightweight cardstock is ideal.  NOT watercolour paper of HEAVY card.  Deli paper is perhaps too thin and certainly too sheer.

3turtlewrap

a bit about that – Ideally, because when the cover papers are wrapped the BACK of the print peeks very slightly into view, a print that has something on the back may be preferable. I also like to drag a  pen or some paint along the edges, just to hide the white core of the cardstock where it’s cut.

10turtlewrap

1. Decide on the orientation of your print.  If it has direction (like text or a masked or stenciled figure) decide if it matters to you if it is sideways.

5turtlewrap

2. Cut the prints.

 Front cover:  Two prints  Back cover: Two prints

  • one print cover width x cover height + 3 inches 
  • one print cover height x cover width + 3 inches

4turtlewrap

I’m showing the two pieces with the boards so you can see the orientation, but you need one of each  size for EACH cover. The print with the flaps top and bottom will be the INSIDE of the Front or Back cover

3. Lay the print face down and place the cover centred on it.  Score along the top and bottom of the coverboard and fold flap A and flap B to wrap.

6turtlewrap

Crease this well with a bone folder.

4. I snip flaps C and D just to make inserting them to wrap a little easier.  Laying the second piece face down, with the longer measurement side to side, score and crease the same way

8turtlewrap

5. Slip one of the side flaps into the gap – it goes between the full front and the board.

9turtlewrap

6. Slip the other side flap in on the opposite side, securing the wraps around the board

10turtlewrap

To add the accordion insert, simply slip the first page into the gap between the INSIDE of the front cover and the board.  Slip the last page into the gap between the board and the INSIDE back cover. The bulk of the cover should be to the OUTSIDE of the “stack” – once you do it, it will be very clear, I promise!

16turtlewrap

You can make the a double-sided book because the back of the accordion is completely usable as well.

17turtlewrap

For my vellum pages version I did NOT make it double-sided and slipped the accordion in like above.   When standing up, and extended, the FRONT and BACK covers can be seen along with the inner “pages”  because it is meant to be displayed, backlit, like so:

flapcover

If you add a spine, that will both hold the book closed and provide a place to stick the tie-closure ribbon/twine/thread/whatever.

15turtlewrap

Cut a piece of a print as tall as the accordion and just wide enough to cover the folded book plus 3 – 4 inches. A single accordion is thin, so an overall measurement of height of coverboard + 4 inches is more than enough. I showed this yesterday with the ribbon stuck to the spine

8artspeak

but I am now thinking two small slits and the ribbon threaded thru is a better option as it’s more secure.   Just make a slit that is as wide as the book is thick. Thread the ribbon thru and wrap to tie.

Slip the side edges of the spine into the gaps between the cover and the book. With the spine in place, you can flip the pages of the book, and if you remove it, you can extend the book for display! Just looking back at the vellum version, here the spine is in place – the book stays closed and the pages turn like a normal book.

4artspeak

So I hope that explains it well enough.  Any questions, ask and I’ll help if I can.

Advertisements

7 thoughts on “Turtle Wrap book cover instructions

  1. Love the book, the how to and the pages. What a great technique and thank you for sharing

  2. so is your accordion 5″ x 30″ ? You didn’t give the measurements for that.
    Thanks

    • To be honest I didn’t actually measure it 🙂 But yes – 20 x 5 is the “pages” you see, then there are two additional pages that are hidden my the covers, equaling 10 inches. But the point is you can make the pages any size you want. The covers and the wraps are then cut to fit YOUR choice using the formula.

      HTH

      MA

  3. Pingback: Circular Flags Flag book instructions | scrappystickyinkymess

  4. Love the book – great instructions! Want to ask about the monoprints you begin with, they have a letter cluster on them that I adore. Is that one of your own creations or a commercial stencil?

    • The letter cluster is a stencil I cut from an image for the Cricut. It’s from the Edge to Edge cart and image 17. I cut the stencils from report cover plastic and although they are thin, they work well with the Gelli plate. HTH

      Mary Anne

Thanks for dropping by. I hope you found something interesting and welcome your feedback. If you ask a question, and don't add your email, do either subscribe to replies or check back. I try to answer every question if I can. Cheers!

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s